MOLTAN CO -- SAFETY ABSORBENT & OIL & GREASE ABSORBENT -- 9610-00N020673
===================== Product Identification ===================== Product ID:SAFETY ABSORBENT & OIL & GREASE ABSORBENT MSDS Date:03/15/1986 FSC:9610 NIIN:00N020673 === Responsible Party === Company Name:MOLTAN CO Address:HWY 125 SOUTH Box:9 City:MIDDLETON State:TN ZIP:38052 Country:US Info Phone Num:901-376-8411 Emergency Phone Num:901-376-8411 Preparer's Name:J.K. FENN CAGE:MLTAN === Contractor Identification === Company Name:MOLTAN CO Address:HWY 125 SOUTH Box:9 City:MIDDLETON State:TN ZIP:38052 Country:US Phone:901-376-8411 CAGE:MLTAN ============= Composition/Information on Ingredients ============= Ingred Name:ACTIVATED MONTMORILLONITE CLAY; (MONTMORILLONITE CLAY) CAS:1318-93-0 Fraction by Wt: 100% OSHA PEL:0.16MG/M3 RDUST(MFR) ACGIH TLV:0.47MG/M3 TDUST(MFR) ===================== Hazards Identification ===================== LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER. Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO Health Hazards Acute and Chronic:INHAL: YEARS OF LONGTERM EXPOSURE TO RESPIRABLE SILICA ABOVE TLV MAY PRODUCE PNEUMOCONIOSIS IN SUSCEPTIBLE PERSONS. MAY IRRITATE NASAL PASSAGES. INGEST/SKIN: NO ADVERSE EFFECTS LIKELY. EYES: MAY IRRIT ATE. Explanation of Carcinogenicity:NOT RELEVANT Effects of Overexposure:SEE HEALTH HAZARDS. Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER. ======================= First Aid Measures ======================= First Aid:INHAL: REMOVE TO FRESH AIR. INGEST: INDUCE VOMITING TO PURGE. SKIN: WASH WITH SOAP AND WATER. EYES: IRRIGATE IMMEDIATELY WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES. DO NOT RUB EYES. OBTAIN MEDICAL A TTENTION IF NECESSARY. ===================== Fire Fighting Measures ===================== Flash Point:NONE Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE . Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL PROTECTIVE EQUIPMENT . Unusual Fire/Explosion Hazard:NONE. ================== Accidental Release Measures ================== Spill Release Procedures:USE CLEANING PROCEDURES SUITABLE FOR ANY INERT DRY PRODUCT. IF SPILL IS ON A WET, OIL OR ICY SURFACE, PERSONAL SAFETY MAY BE ENHANCED BY LEAVING SPILLED MATERIAL TO ABSORB WATER OR OIL TO IMPROVE TRAC TION. Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER. ====================== Handling and Storage ====================== Handling and Storage Precautions:STORE IN DRY AREA. Other Precautions:NONE. ============= Exposure Controls/Personal Protection ============= Respiratory Protection:NIOSH/MSHA APPROVED DUST RESPIRATOR WHEN LARGE QTY USED. Ventilation:NONE REQUIRED OTHER THAN NORMAL. Protective Gloves:IMPERVIOUS GLOVES . Eye Protection:CHEMICAL WORKERS GOGGLES . Other Protective Equipment:NONE. Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER. Supplemental Safety and Health SPEC GRAV: 2.45-2.52(H*2O=1). ================== Physical/Chemical Properties ================== HCC:N1 Spec Gravity:SUPP DATA Solubility in Water:0.7% Appearance and Odor:GRANULAR CLAY; BUFF TO GRAY; ODORLESS ================= Stability and Reactivity Data ================= Stability Indicator/Materials to Avoid:YES NONE. Stability Condition to Avoid:NONE. UNDER SOME CNDTNS, COMBINATIONS W/CERTAIN SOLV MAY INCR TEMPERATURE SLIGHTLY. NO HAZARD. Hazardous Decomposition Products:NONE. ==================== Disposal Considerations ==================== Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH STATE, FEDERAL OR LOCAL LAWS. Disclaimer (provided with this information by the compiling agencies): This information is formulated for use by elements of the Department of Defense. The United States of America in no manner whatsoever, expressly or implied, warrants this information to be accurate and disclaims all liability for its use. Any person utilizing this document should seek competent professional advice to verify and assume responsibility for the suitability of this information to their particular situation.